اسیلوسکوپ دستی هانتک مدل HANTEK DSO-8202E

اسیلوسکوپ دستی هانتک مدل HANTEK DSO-8202E دارای مشخصات فنی زیر است:

• اسیلوسکوپ دستی
• دیجیتال
• 200 مگاهرتز
• 2 کانال
• حافظه دار
• سرعت نمونه برداری 1 گیگا سمپل بر ثانیه
• دارای دو عدد پراب داخل بسته محصول
• فانکشن FFT
• دارای فانکشن ژنراتور 25 مگاهرتز قابل برنامه ریزی با رزولوشن 12Bit به همراه پراب فانکشن
• حافظه داخلی 2Mpoint
• نمایشگر TFT رنگی 7 اینچ
• دارای مولتی متر دیجیتال
• بیش از 20 نوع اندازه گیری اتوماتیک
• دارای پورت USB2.0
• دارای کیف حمل
• دارای شارژر و پراب مولتی متر داخل بسته محصول

• Model	DSO-8072E	DSO-8102E	DSO-8152E	DSO-8202E
  Bandwidth	70MHz	100MHz	150MHz	200MHz
  Acquisition
  Sample Modes	Real-Time Sample
  Acquisition Modes
  Normal	Normal data only
  Peak Detect	High-frequency and random glitch capture
  Average	Waveform Average, selectable 4,8,16,32,64,128
  Inputs
  Inputs Coupling	AC, DC, GND
  Inputs Impendance	1MΩ±2% ‖20pF±3pF
  Probe Attenuation	1X, 10X
  Supported Probe Attenuation Factor	1X, 10X, 100X, 1000X
  Maximum Input Voltage	CAT I and CAT II: 300VRMS (10×), Installation Category; CAT III: 150VRMS (1×)
  Horizontal System
  Sample Rate Range	1GS/s
  Waveform Interpolation	(sin x)/x
  Record Length	2M
  SEC/DIV Range	4ns/div~2000s/div, in a  2, 4, 8 sequence		2ns/div~2000s/div, in a  2, 4, 8 sequence
  Sample Rate and Delay Time Accuracy	±50ppm over any ≥1ms time interval
  Scanning Speed Range	4ns/div to 8ns/div; (-8div x s/div) to 40ms; 20ns/div to 80μs/div;(-8div×s/div) to 40ms; 200μs/div to 40s/div;(-8div×s/div) to 400s;		2ns/div to10ns/div;(-4div×s/div) to 20ms;
  Delta Time Measurement Accuracy (Full Bandwidth)	Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns); >16 averages:± (1 sample interval + 100ppm × reading + 0.4ns); Sample interval = s/div ÷ 200
  Vertical System
  Vertical Resolution	8-bit resolution, all channel sampled simultaneously
  Volts Range	2mV/div to 100V/div at input BNC
  Rise Time at BNC( typical)	5ns	3.5ns	2.3ns	1.8ns
  Analog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled	±400V(100V/div-20V/div); ±50V(10V/div-5V/div); ±40V(2V/div-500mV/div); ±2V(200mV/div-50mV/div); ±400mV(20mV/div-2mV/div);
  Math	+, -, *, /, FFT
  FFT	Windows:  Hanning, Flatop, Rectamgular, Bartlett, Blackman; 1024 sample point
  Bandwidth Limit	20MHz
  Low Frequency Response (-3db)	≤10Hz at BNC
  DC Gain Accuracy	±3% for Normal or Average acquisition mode, 100V/div to 10mV/div. ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div.
  DC Measurement Accuracy, Average Acquisition Mode	Measurement Type: Average of ≥16 waveforms with vertical position at zero Accuracy: ± (3% × reading + 0.1div + 1mV) when 10mV/div or greater is selected. Measurement Type: Average of ≥16 waveforms with vertical position not at zero Accuracy: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div].
  Volts Measurement Repeatability, Average Acquisition Mode	Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions
  Trigger System
  Trigger Types	Edge, Video, Pulse, Slope, Over time, Alternative
  Trigger Source	CH1, CH2, AC Line
  Trigger Modes	Auto, Normal, Single
  Coupling Type	DC, AC, HF Reject, LF Reject, Noise Reject
  Trigger Sensitivity (Edge Trigger Type)	DC(CH1,CH2): 1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full; AC: Attenuates signals below 10Hz ; HF Reject: Attenuates signals above 80kHz; LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz.
  Trigger Level Range	CH1/CH2: ±8 divisions from center of screen;
  Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20ns	CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen;
  Set Level to 50%(typical)	Operates with input signals ≥50Hz
  Video Trigger
  Video Trigger Type	CH1, CH2: Peak-to-peak amplitude of 2 divisions;
  Signal Formats and Field Rates	Supports NTSC, PAL and SECAM broadcast systems for any field or any line
  Holdoff Range	100ns ~ 10s
  Pulse Width Trigger
  Pulse Width Trigger Mode	Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse
  Pulse Width Trigger Point	Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level. Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width. Less than: The trigger point is the trailing edge. Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width
  Pulse Width Range	20ns ~ 10s
  Slope Trigger
  Slope Trigger Mode	Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope
  Slope Trigger Point	Equal: The oscilloscope triggers when the waveform slope is equal to the set slope. Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope. Less than: The oscilloscope triggers when the waveform slope is less than the set slope. Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.
  Time Range	20ns ~ 10s
  Overtime Trigger
  Over Time Modee	Rising edge or Falling edge
  Time Range	20ns ~ 10s
  Alternative Trigger
  Trigger on CH1	Internal Trigger: Edge, Pulse Width, Video, Slope
  Trigger on CH2	Internal Trigger: Edge, Pulse Width, Video, Slope
  Trigger Frequency Counter
  Readout Resolution	6 digits
  Accuracy (typical)	±30ppm (including all frequency reference errors and ±1 count errors)
  Frequency Range	AC coupled, from 4Hz minimum to rated bandwidth
  Signal Source	Pulse Width or Edge Trigger modes: all available trigger sources The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed. Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time. Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity. Video Trigger mode: The Frequency Counter does not work.
  Measure
  Cursor Measurement	Manual: Voltage difference between cursors: △V Time difference between cursors: △T Reciprocal of △T in Hertz (1/ΔT); Tracing: The valtage and time at a waveform point;
  Auto Measuerment	Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS,
  Waveform Generator Mode
  Frenquency Range	1Hz(DC)~25MHz
  DAC Clock	2K~200MHz adjustable
  Memory Depth	4KSa
  Vertical Resolution	12 Bits
  Stability	<30ppm
  Amplitude	±3.5V Max.
  Output Impedance	50 Ω
  Output Current	50mA Ipeak=50mA
  System Bandwidth	25M
  Harmonic Wave Distortion	-50dBc(1KHz),  -40dBc(10KHz)
  General Specifications
  Display Resolution	640 horizontal by 480 vertical pixels
  Display Contrast	Adjustable (16 gears) with the progress bar
  Probe Compensator Output
  Output Voltage( typical)	About 2Vpp into ≥1MΩ load
  Frequency(typical)	1kHz
  Power Supply
  Supply Voltage	AC Input:100-240VACRMS,0.6A MAX,50Hz~60Hz; DC Output:9V,2A
  Power Consumption	<30W
  Environmental
  Temperature	Operating: 32℉ to 122℉ (0℃ to 50℃); Nonoperating: -40℉ to 159.8℉ (-40℃ to +71℃)
  Cooling Method	Convection
  Humidity	+104℉ or below (+40℃ or below): ≤90% relative humidity; 106℉ to 122℉ (+41℃ to 50℃): ≤60% relative humidity
  Altitude	Operating: Below 3,000m (10,000 feet); Nonoperaring: Below 15,000m(50,000 feet)
  Mechanical
  Size	260mmmm; 220mm; 75mm
  Weight	2.5KG(without Packing)